SP-CFF – Polish Club Flora Fauna AWARD 6

update to 6

SP-CFF- Polish-Club-Flora-Fauna

90 Years of IARU

iaru-40M-1541 iaru-PHONE-1820


France Flora Fauna 5



The remoterig configuration


Radio settings
Program mode 2 – IC-7100, IC-706, IC-703
Sip password  xxyyyzzz
Sip contact(Radio RRC IP/hostname)
Auto connect NO
Audio quality 2 – Linear 16 bits 8 kHz
Audio left/right ch swap NO
Codec out gain 255
Codec inp gain 60
Codec inp HPF Hz 163
Codec inp preamp YES
COM0 baudrate 38400
COM0 data bits 8
COM0 stop bits 1
COM0 parity 0
COM0 Program mode 3 char timeout 2
Use USB Com Port as COM0 NO

Serial Settings

COM2 mode Mode-2, ICOM CI-V
COM2 baudrate 9600
COM2 data bits 8
COM2 stop bits 1
COM2 parity 0
COM2 terminator (hex) 88
Use USB Com Port as COM2 Yes

Advanced Settings

UDP cmd port 13002
UDP audio port 13001
SIP port 13000
Web server port 80
Telnet server port 23
Rx jitter buffer size 4
Rx jitter delay 3
Audio packet size (ms) 20
RTP tx mode Continuous
Disable audio tones No
Audio tones -db [70-0] 30
IP identification (morse) No
Full duplex No
PTT-off mute delay 0
IP Type-of-Service (dec) 0
UDP cmd min-data-size 0
Use common network settings No



My actual setup IC7100 + Remoterig – Part I

My actual setup is based on a Icom IC7100. It is great radio in my opinion also if you use in a remote configuration like me.
My antenna, actually a Titan DX, is placed in my parents house for several reasons. The most important one is that is at about 900 mt a.s.l. and as no obstacle towards see coast.
The cons of my parents house is that the actual adsl connection is really poor and achieves speed around 400-500 Kb/s.
For this reason I tried in the past years several combination, mostly using a remote pc for cat connection and voice transmission (skype, mumble, teamviewer, vnc and so on).
I also tried a combo with raspberry and some audio card, but everything was really unstable, mostly because the low speed of internet connection.
When I bought the IC7100 I decided to invest some more money in something more stable and after some research I selected the remoterig device.

This solution for the IC7100 is perfect because you can bring the front part at your remote location and attach directly to the remoterig control and there is no difference from connecting directly to the rig.

This is a perfect solution if you want to use the voice.

For the CAT connection is a little more complex and I have to say that from the forum of the remoterig seller you receive few information but being patience it is possible to solve  the puzzle and after everything became clear.

So for you that are looking for a complete solution I can suggest to proceed in the following way taking really care of particulars, of course I will consider that you are able to setup the remote connection properly and you know where are you putting your hands.



DXFF 10H Flora e Fauna




WWFF award 10


RaspberryPi for radio remote control with voice support

In the last month, I worked over the optimization of my remote radio station. I have a Yaesu FT897D in my parents QTH in a wonderful open position and I would like from my house in city.

It was not a big problem to setup a remote station using a notebook running the HRD server and controlling the radio via CAT. I had some minor problem in obtaining the best voice modulation using the notebook soundcard. I’m working on it and I hope to solve it quickly. For the voice connection actually I use a classical skype connection. Everything is working quite well despite the frequent crashes of HRD, probably due to the low bandwidth of my parents QTH.

Furthermore I would like to save a notebook only for this activities so I started investigating on Rpi and its implementation. As many of you know in the raspbian distribution there are already the hamlib library and various tool for CAT control (see hamlib net control) . The Yaesu FT897 is poorly implemented but there is the possibility to improve the basic controls.

The other brick completing the set is the Wolfson Audio Card for Raspberry: it is a powerful low cost soundcard that can be fitted on raspberry giving the possibility to a) recording audio and b) using some nice DSP voice feature. The drivers for this card are going to be integrated in the latest version of raspbian kernel distribution, but it is possible to do a lot already with the 3.10 kernel (follow this user guide for installing it).

For the audio part I’m going to use the VoIP smartphone software linphonec that is compatible with wolfson audio card (doing some hacking for downsampling to 8kbit the streaming).

I also verified the the Kernel 3.10 support the USB-CAT cable based on my Prolific 2303 chipset.

Actually I have all the pieces of the puzzle in my hand and I’ll update this post as soon with details trying to provide a step-by-step tutorial.


PS: I was thinking to name this project RASPAM “rasp-ham-remote” but I open to suggestion 🙂

UPDATE (Dec 29, 2014): Thanks to Giovanni Moretti ZL2GX from New Zeland for name suggestion that for the moment sounds an improvement for the project name. About the Wolfson Audio Card: I think that the support from the producers is still unsufficient. I’m following the GITHub contribution from wolfsonmicro stuff and the last activity was one month ago.


IT Navy Ship Award 2014